37 Egerton Street, Southport QLD 4215Mon to Fri 8am to 5pm, Sat 8am to 1pm4.9from 2,952 Google reviews
Southport Budget Tyres & Auto (07) 5527 0004
Blog

Legal tyre tread depth in Queensland

The legal minimum is 1.5 mm. That is the floor, not a target. Wet grip falls away before you get there, and a free tread check will tell you where you stand.

By Southport Budget Tyres & Auto

4.9from 2,952 Google reviews

Tyre size

Find your tyre size

The size is moulded into the sidewall, for example 205/55R16. Choose the three numbers, then call for a price.

Build your size

Choose the three numbers off your sidewall and we will write the size for you. Then call, or send it through on a quote.

205/55R16

How to read your tyre size

How to read a tyre size, using 205/55 R16 91V as an example A photograph of a tyre sidewall with the marking 205/55 R16 91V. 205 is the width in millimetres. 55 is the profile, the sidewall height as a percentage of the width. R16 is radial construction on a 16 inch rim. 91 is the load index, 615 kilograms. V is the speed rating, 240 kilometres an hour. WIDTH205 mm PROFILE55% RIMR16 (radial, 16 inch) LOAD91 SPEEDV How to read a tyre size, using 205/55 R16 91V as an example A photograph of a tyre sidewall with the marking 205/55 R16 91V. 205 is the width in millimetres. 55 is the profile, the sidewall height as a percentage of the width. R16 is radial construction on a 16 inch rim. 91 is the load index, 615 kilograms. V is the speed rating, 240 kilometres an hour. 1 2 3 4 5
  1. Width (205 mm)
  2. Profile (55% of width)
  3. Construction and rim size (R = radial, 16 inch)
  4. Load index (91)
  5. Speed rating (V)

The rule, in plain language

In Queensland, a tyre on a light vehicle must have a tread pattern at least 1.5 mm deep in all principal grooves, other than at the tread-wear indicators. That tread must run in a continuous band across the part of the tyre that normally meets the road, and around the whole circumference of the tyre. A good-looking patch in one spot is not enough.

That comes from Schedule 1, section 52 of Queensland's 2021 light vehicle standards (the Transport Operations (Road Use Management, Vehicle Standards and Safety) Regulation 2021). The same 1.5 mm figure is used in Queensland's test-vehicle requirements. It is a legal minimum for the tyre to be on the road, and it is also what a safety certificate inspection is looking for on tread depth.

Principal grooves are the wide grooves, usually in the centre of the tread or running across it, where the wear indicators sit. Secondary, shallow grooves can disappear as the tyre wears and are not the measure.

How to check it yourself

Look into the main grooves for the small rubber bars that sit across them. Those are the tread-wear indicators. When the tread is worn level with those bars, you are at the end of the legal tread. Do not wait until you can see canvas or a smooth patch.

Check more than one place on each tyre, and check all four tyres, plus the spare if you have one. Wear is often worse on one shoulder, or on one side of the car. A coin can give you a rough idea, but a proper gauge or a workshop check is better, especially if the car is close to a roadworthy or a long trip.

If the wear is uneven, depth is only half the story. A tyre can still be at 1.5 mm in the centre and be scrubbed on the edge. That is usually pressure, alignment or a suspension issue. See signs you need a wheel alignment.

Roadworthy inspections and everyday driving

If you need a roadworthy certificate to sell or transfer the car, tyres are an easy place to fail. Depth has to meet the rule around the tyre, and damage, exposed cords or the wrong rating can also be a reason for rejection. Do not leave the tyres until the morning of the inspection.

For everyday driving the same standard applies. A tyre below 1.5 mm is not legal to use, even if 'it still looks all right from the footpath'.

We do a free tread check at 37 Egerton Street, Southport, with no obligation. If a tyre should come off, new and used replacements start from $35 fitted. Used tyres we fit have up to 90% tread, which is a long way above the legal floor.

If you are close to the limit, come in

Call (07) 5527 0004 or drive in. We will measure the tyres, show you what we find, and quote options rather than one take-it-or-leave-it line. We'll beat any quote or your tyres are FREE. Afterpay, Zip and humm are available.

Most replacements are done while you wait. If only one tyre is down and the others are even and healthy, a single match may be enough. If a pair is down, replace them together.

For month-to-month habits that keep you off the limit, see how to maintain your wheels and tyres.

FAQ

Common questions

What is the legal tyre tread depth in Queensland?

1.5 mm in all principal grooves, other than at the tread-wear indicators, in a continuous band across the contact face and around the whole tyre.

Is 3 mm the legal minimum?

No. In Queensland the legal minimum is 1.5 mm. Replacing earlier can still be wise for wet-weather grip.

Do you check tread for free?

Yes. Drive in to 37 Egerton Street, Southport, for a free tread check. There is no obligation.

If one tyre is under 1.5 mm, do I have to replace all four?

Not always. We will measure the others. A single matching tyre can be enough if the rest of the axle is even and healthy. A pair should be replaced together if both are down.

Talk to the team now

Fit while you wait. 5 fully qualified mechanics on site.

Call (07) 5527 0004

Mon to Fri 8am to 5pm, Sat 8am to 1pm

Afterpay, Zip and humm available.Afterpay logoZip logohumm logo

Get a quote

ENQUIRE NOW

Need tyres or a check today?

We'll beat any quote or your tyres are FREE. New and used tyres from $35 fitted, fit while you wait.

Call (07) 5527 0004Get a quote